New electrical distribution equipment, built around your projectServing Georgia
Rows of gray electrical switchgear cabinets on pallets in a large indoor space.

Protection

Voltage Transformer Selection for Relaying

Voltage transformer selection affects whether relays and meters receive usable signals across normal operation and fault conditions. For Georgia engineers, contractors and facility teams, a sound specification starts with system voltage and connected functions, then resolves ratio, accuracy, fusing and grounding with the protection design. This guide outlines decisions to coordinate before ordering new equipment.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Start with the system and function

Identify the nominal and maximum system voltage, frequency, phase arrangement, and grounding method at the point where voltage will be measured. Clarify whether the transformer is connected phase-to-phase, phase-to-ground, or in another arrangement. The primary connection and secondary outputs must suit the one-line diagram and the relay scheme; a ratio chosen from nominal voltage alone may not provide the required signal during ground faults or abnormal conditions.

List every intended use: protective relays, metering, synchronizing, voltage indication, or controls. Note which functions must remain available during a blown fuse or loss of a phase. A relay may need a particular residual or open-delta voltage input for ground-fault logic, while revenue or operational metering can have different accuracy needs. Have the protection engineer confirm the intended circuit and signals rather than assuming one secondary serves every purpose.

Choose ratio and secondary outputs

Specify primary and secondary voltage values in the format used by the project drawings, and state whether the ratio is per phase or line-to-line. Confirm that the selected ratio matches the relay or meter input range and the voltage reference used by its settings. Where equipment may operate at more than one system voltage, provide the operating configurations and switching method so the design can address each condition explicitly.

If separate circuits are needed for protection and indication, determine whether separate secondary windings or transformers are appropriate. Identify required terminal connections, polarity markings, grounding reference, and any residual-voltage connection. The drawing package should show which secondary feeds which device, including any test or isolation provisions required by the maintenance plan. Avoid relying on a generic ratio description when the connection and relay logic determine the actual delivered voltage.

Match accuracy to the duty

Ask the engineer to define accuracy requirements for each connected function and the voltage range over which they apply. Protective relaying requirements may focus on dependable input for specified elements and operating conditions; metering may call for accuracy over a stated range of normal load voltage. Confirm the applicable accuracy class and burden basis from the project specification and manufacturer data, rather than assuming a transformer suitable for one duty will meet another.

Account for the total connected burden, including relay, meter, wiring, and any other devices on the secondary. Long wire runs add resistance and can affect voltage at the device, so provide approximate conductor length and gauge or the design assumptions. Check that the intended load remains within the selected transformer's capability while maintaining the required performance. If loads or devices may change, identify that possibility for engineering review before the configuration is finalized.

Coordinate fusing and grounding

Specify primary and secondary fusing requirements in coordination with the protection design, equipment construction, and applicable project standards. Fuse selection and placement affect fault isolation and the risk of losing voltage inputs; do not treat fuse size or interrupting capability as a field guess. Clarify whether fuses, holders, disconnecting features, or specified fuse indication are required, and provide the relevant system fault information for the engineer to evaluate the arrangement.

Define the secondary grounding point and grounding method on the drawings. A grounded secondary reference can help establish a stable measurement, while multiple grounding points can create unwanted paths or incorrect readings. The primary grounding arrangement and transformer connection also influence what the relays see during ground faults. Coordinate these details with the complete protection scheme and facility grounding design; installation and testing should be performed by qualified personnel under approved project procedures.

Prepare the specification and handoff

For a quote, share the one-line diagram, nominal and maximum voltage, frequency, primary connection, system grounding method, required ratios, and each relay or metering function. Include accuracy requirements, secondary burden or connected-device data, fusing preferences, grounding details, enclosure or switchboard arrangement, and applicable drawings or project specifications. Identify any special test access, terminal labeling, or separation between protection and indication circuits.

State the Georgia project location, delivery point, required on-site date, and any receiving or access constraints so shipping and order planning can be reviewed for the actual configuration. New switchgear and transformer arrangements are built to the confirmed scope; availability and timeline depend on the order details. Before release, reconcile the approved drawings, relay settings assumptions, ratio labels, fuse schedule, and grounding instructions. Close these items with the protection engineer and purchasing team, then carry the approved documents into installation and commissioning.

A practical final check is to trace each voltage input from the transformer primary connection through its fuse and secondary wiring to the assigned relay or meter terminal. Confirm the expected normal reading and the intended response to loss of a phase or ground-fault condition against the approved scheme. Resolve discrepancies before equipment release, and use the verified schedule as the basis for procurement, field wiring, and commissioning.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote