New electrical distribution equipment, built around your projectServing Georgia
Three gray electrical switchgear cabinets on pallets, with a door swung open.

Protection

Synchronism Check Relays

Connecting an energized generator, bus, or utility source to another live source requires more than a breaker command. For Georgia engineers, contractors, and facility teams, a synchronism-check relay adds a permissive only when configured electrical conditions are met. This guide explains the checks, design inputs, and procurement details to resolve before specifying a new switchgear assembly.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Why the closing instant matters

When two energized sources are connected, differences in voltage magnitude, frequency, or phase angle can produce substantial current and mechanical torque at the instant the breaker closes. The consequences depend on the system, equipment, and operating conditions; a close that is acceptable for one application may be unsuitable for another. Synchronism-check protection is intended to block a closing operation when measured conditions fall outside approved limits.

The relay typically compares voltage signals from the two sides of a circuit breaker and grants a close permissive when configured criteria are satisfied. It does not decide whether paralleling is allowed by the facility’s operating rules, utility agreement, or protection design. Those requirements must be established by the responsible engineer and coordinated with the control scheme.

Define the sources and operating modes

Start by identifying exactly which sources may be connected and under what conditions: utility to generator, generator to an energized bus, or one live bus section to another. Distinguish those cases from dead-bus closing, where one side has no voltage, and from transfer schemes that are intended to avoid paralleling. A synchronism-check function may not be the correct permissive for every mode.

Document normal and abnormal operating sequences, including automatic transfer, manual close, generator synchronization, and restoration after an outage. Specify whether the relay supervises every closing path or only selected commands. If multiple sources or breakers are involved, provide a one-line diagram and describe interlocks so the engineer can determine which voltage references and close circuits belong to each check.

Specify measurable criteria and signal sources

Engineering must select the allowable voltage difference, frequency difference or slip, and phase-angle window for the application. The closing window should account for breaker operating time, since the electrical conditions continue changing between a permissive and contact separation. Relay settings therefore need to reflect the breaker and control scheme, not just a general assumption that the sources are synchronized.

Identify voltage-transformer locations, ratios, phase connections, grounding arrangements, and available secondary signals on both sides of the breaker. Confirm which phases the relay will compare and how loss of a voltage signal is detected. Share relay make and model requirements if already selected, along with control voltage, close-coil interface, wiring conventions, and any required indication or event outputs. Final settings and connections require engineering review.

Coordinate protection with the closing circuit

A synchronism-check relay generally provides supervision rather than initiating a close by itself. The scheme must define how its permissive interacts with operator commands, automatic controls, breaker anti-pump logic, lockout devices, and other interlocks. Determine what the circuit does when voltage inputs are invalid, the relay is unavailable, or an alternate operating mode is selected; bypasses, if permitted, need deliberate authorization and clear control.

Review the full trip-and-close logic and the intended response to failures before procurement. Confirm whether the relay is furnished as a separate control component or incorporated into a switchgear control package, and identify required terminals, test provisions, labels, and drawings. A new UL 891 switchboard assembly may be relevant to a low-voltage project, but UL 891 applies to switchboards and does not establish a blanket listing for medium- or high-voltage switchgear.

Prepare the project handoff and quote inputs

For a useful quote, provide the one-line diagram, system voltage, source types, breaker details, control voltage, voltage-transformer information, and the operating sequences the relay must supervise. Include the preferred relay or approved alternatives, required communications or alarms, enclosure and switchgear arrangement, drawing standards, and any interface with existing equipment. Clearly mark information that is preliminary so design assumptions are not mistaken for approved settings.

Also identify the project location in Georgia, delivery destination, required ship-to coordination, and the dates that govern submittals, approvals, and installation planning. We manufacture and supply new switchgear in the United States, with custom-built configurations, American-made components, and nationwide shipping; exact scope, component availability, and schedule are confirmed for each order. Georgia delivery planning should align with site access and the project sequence, not assume a fixed transit or arrival date.

Close out settings, drawings, and acceptance

Before release, the responsible engineer should approve the synchronism-check settings, voltage references, logic narrative, and interfaces with the breaker control circuit. Coordinate drawing review with the protection study and applicable utility or facility requirements. Confirm who supplies final settings, who verifies wiring and relay configuration, and what documentation is needed for commissioning; do not treat a permissive indication as proof that the complete scheme is correctly configured.

For commissioning, qualified personnel should verify voltage inputs, phase relationships, relay logic, close permissives, and blocking behavior against the approved procedure, with the breaker handled under site safety controls. To begin specification, send the one-line, source and transfer scenarios, breaker and instrument-transformer data, control requirements, and Georgia delivery constraints. That information helps define a switchgear scope that supports the intended synchronization checks without substituting for project engineering approval.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote