New electrical distribution equipment, built around your projectServing Georgia
Row of gray electrical control cabinets with switches and indicator lights.

Design

Switchgear Short-Circuit Study Inputs

A useful short-circuit study begins with accurate system data, not a switchgear catalog rating. Georgia engineers, contractors, and facilities teams can use this checklist to assemble source, transformer, conductor, and motor information for the study and to coordinate resulting requirements with a new switchgear order.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Define the study boundary

Identify the one-line diagram revision, project phase, operating configurations, and buses or equipment included in the analysis. Mark the point of utility service, transformers, generators, major motors, ties, and the proposed switchgear lineup. State whether the study must evaluate maximum available fault current, minimum fault current, or both, and identify the fault types and locations the engineer will analyze.

Document normal and alternate arrangements, including open or closed tie breakers, parallel transformers, standby sources, and any temporary construction feeds. A result calculated for one lineup configuration may not represent another. Share expected operating modes and planned changes rather than asking the study engineer to infer them from an incomplete drawing.

Request complete source data

For a utility source, provide the serving utility’s available short-circuit current or Thevenin equivalent at the service point, with voltage and whether the value is maximum or minimum. Include X/R ratio when available, the date and source of the data, and any stated assumptions about upstream system configuration. If the utility supplies sequence impedances or separate three-phase and line-to-ground values, pass those through without converting or rounding them.

For onsite generators or other sources, provide manufacturer data and operating details, including rated voltage, kVA or kW, subtransient reactance where available, grounding arrangement, and whether units can operate in parallel. Confirm which sources are present for each study case. If utility fault data is pending, identify that dependency early; a provisional study assumption should be labeled, not treated as a confirmed equipment requirement.

Capture transformer nameplate details

Record each transformer’s rated kVA, primary and secondary voltages, percent impedance, winding connection, and available nameplate X/R data. Include manufacturer and serial details if useful for matching field equipment to records. Confirm whether the impedance value is based on the actual unit or a preliminary specification, and note any permitted impedance tolerance that could affect the study case.

Describe tap position or range, grounding method, neutral connection, and any grounding resistor or reactor with its rating and location. For multiple transformers, state whether they normally serve separate sections or may be paralleled. These details affect the path and magnitude of fault current; do not assume that identical kVA ratings mean identical contribution or operating conditions.

Map conductors and system connections

For each segment between sources, transformers, switchgear, and major loads, provide conductor material, size, number of parallel sets, length, insulation or cable type, and installation arrangement when known. Include bus duct or busway impedance data, feeder lengths, and the connection points for ties. Identify whether lengths are measured, estimated, or taken from design drawings, and flag sections whose routing has changed in the field.

Provide grounding and bonding details relevant to the modeled system, including neutral conductors and grounding paths. The study engineer may need conductor sequence impedance or manufacturer data for certain analyses, particularly where line-to-ground faults matter. Clear segment labels that match the one-line diagram help prevent an impedance value from being assigned to the wrong feeder.

Account for motor contribution

List significant motors connected to the buses under study, with quantity, horsepower or kW, rated voltage, and motor type. Distinguish induction motors from synchronous motors and identify large groups of similar motors where individual nameplates are unavailable. Provide starting or operating status for each relevant study case, along with available subtransient reactance or manufacturer contribution data.

Include motor control center and drive information where it affects the modeled connection. Variable-frequency drives do not necessarily contribute fault current like directly connected motors; provide drive topology and manufacturer data rather than applying a generic motor assumption. Identify loads that may be disconnected, transferred, or operating through bypass arrangements in alternate modes.

Turn study results into switchgear requirements

Ask the engineer to state the calculated fault current at each relevant bus, the modeled configuration, source assumptions, and any unresolved data. Share the study output and its revision with the switchgear manufacturer, along with the one-line diagram, nominal system voltage, lineup arrangement, and intended protective-device information. Equipment selection and design require review against the project’s complete electrical requirements and applicable authority decisions.

For a Georgia project quote, clarify the delivery location, required ship-to access, target project milestones, and whether the study is final or still being updated. Ask what additional drawings or data are needed to define the new equipment, including any custom-built configuration and UL 891 switchboard assembly scope. American-made components and nationwide shipping may be considered where applicable; exact scope, availability, and timing are confirmed for the order. Before requesting a quote, reconcile the study revision with the one-line diagram and list every outstanding source or motor assumption.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote