Set intervals by risk and operating history
There is no single inspection interval that fits every switchgear lineup. Establish a baseline survey after equipment is placed in service and has operated under representative conditions, then set repeat intervals with the facility’s electrical maintenance program. Consider equipment age, loading, switching duty, environment, prior findings, operating criticality, and the consequences of an outage. A lineup with recurring temperature differences or a history of loose connections may warrant closer follow-up than equipment with stable records.
Use applicable maintenance standards, site procedures, equipment instructions, and a qualified electrical professional’s judgment to define the schedule. Also account for changes that can alter thermal behavior, such as added loads, new feeders, maintenance, or a change in operating pattern. If a survey cannot be performed at the planned interval, record the reason and revised date rather than treating the missed check as a completed inspection.
Plan inspections around representative load
Thermal readings are most useful when equipment is carrying a meaningful, documented load. A lightly loaded bus or feeder may not reveal a developing high-resistance connection. Coordinate the survey with operations so the relevant sections have been energized and operating long enough to reach a reasonably stable condition, while avoiding assumptions that every circuit will have the same load. Record measured or available load information and note any unusual operating state.
Inspection access must not compromise electrical safety or operating controls. Only qualified personnel using procedures and protective measures appropriate to the equipment should conduct the survey. Enclosure design, barriers, access provisions, and site rules may limit what can be viewed; do not remove covers or alter safeguards solely to obtain an image without an approved, qualified work plan. A survey plan should identify the lineup, inspection points, access limits, and any circuits that could not be assessed.
Make repeat surveys comparable
Trend data is valuable only when later observations can be compared with earlier ones. Keep a consistent asset identifier for each lineup, section, and inspection point. Record the survey date and time, operating mode, approximate or measured load, ambient conditions when available, instrument details, and the viewing location. Save both thermal and corresponding visual images, with enough context to identify the component without relying on an inspector’s memory.
Temperature alone does not establish the cause or urgency of a finding. Comparisons should consider similar phases or components under comparable loads, emissivity and viewing limitations, and the instrument’s stated measurement constraints. Preserve the original readings and image files, and document any interpretation separately. If operating conditions differ substantially between surveys, flag that limitation; avoid presenting a simple temperature change as a confirmed deterioration trend.
Turn findings into tracked corrective actions
A useful report connects each observation to a specific asset and a clear next step. Document the location, affected component, observed temperature pattern, comparison basis, operating conditions, image references, and the inspector’s recommended priority or follow-up. Distinguish an observed anomaly from a confirmed defect: thermography can identify a thermal pattern, but diagnosis may require further evaluation by qualified personnel under appropriate work controls.
Assign each recommended action an owner, due date, status, and closeout evidence under the facility’s maintenance process. Record the work performed, parts or connections addressed as applicable, and whether a follow-up survey was completed under comparable load. Escalate findings through site procedures when operational risk requires it. Do not assume that a temperature reading alone authorizes continued operation, repair methods, or an equipment rating change.
Use survey history in equipment planning
Repeated findings can inform maintenance and capital decisions, but procurement should begin with the actual equipment scope. When considering a new switchboard or replacement section, gather the lineup identification, system voltage and configuration, main and feeder requirements, available fault-current information, enclosure and environmental needs, physical dimensions, termination details, and the applicable project specifications. Include survey images and reports when they help explain the problem, while having the responsible engineer confirm design inputs and required ratings.
For a manufacturer quote, share the equipment type and scope, drawings or schedules available, site operating constraints, required delivery destination in Georgia, and the project’s requested schedule. Identify whether the request is for a complete new assembly, a replacement section, or another defined configuration. Exact scope, component availability, and timeline are confirmed for each order. For switchboards specified to UL 891, identify that requirement explicitly; it applies to switchboard assemblies and does not establish a listing for other classes of switchgear.
Coordinate the handoff and next survey
Before ordering new equipment, align the engineering and procurement teams on approved drawings, interfaces with existing gear, site access, receiving arrangements, and the planned outage or installation sequence. Confirm who will review submittals, resolve field dimensions, and record changes. Delivery to a Georgia project should be coordinated with the site’s receiving capacity and installation schedule; shipping arrangements and timing depend on the specific order and destination.
Keep the lifecycle record open after installation or corrective work. Add the equipment identification and final documentation to the asset history, establish the next survey date based on the approved maintenance plan, and specify the operating conditions needed for a useful comparison. To prepare a quote, send the scope, available electrical and mechanical documents, survey findings, destination, and requested schedule together. This gives engineering and procurement a practical basis to confirm the configuration and project handoff.