New electrical distribution equipment, built around your projectServing Georgia
Gray electrical switchgear cabinets on wooden pallets, viewed at an angle.

Design

Switchgear Flood Elevation Planning

For Georgia engineers, contractors and facility planners, flood exposure belongs in switchgear location decisions before foundations and room layouts are fixed. Elevation, drainage, access and replacement consequences affect both the installation plan and the equipment configuration. Share site conditions and project constraints early so new switchgear can be specified and delivered to fit the design intent.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Start with the site’s flood basis

Identify the flood information governing the project before selecting an equipment location. This may include mapped flood zones, a project flood study, local design criteria, anticipated water levels, and any required freeboard. The applicable basis depends on the site, facility function and authority having jurisdiction; a map alone may not resolve local drainage or stormwater exposure.

Ask the civil and structural teams to establish the relevant elevation datum and provide proposed finished-floor, grade and equipment-pad elevations. Confirm whether the design basis considers coastal surge, riverine flooding, intense rainfall, ponding or more than one source. Share the controlling documents and assumptions with the switchgear manufacturer so the equipment interface can be reviewed against the actual project criteria.

Compare room, pad and access elevations

A room above grade can still face water entry through low door thresholds, cable trenches, conduits, ventilation openings or adjacent service spaces. For outdoor equipment, compare the proposed pad with surrounding grades and likely flow paths, not only the mapped flood elevation. Consider whether grading, barriers or drainage features could redirect water toward the equipment or obstruct access during a storm.

Elevation changes affect practical installation details. Confirm entry routes for the equipment, door and working clearances, overhead restrictions, conduit stub-ups, cable bend space and the connection point to the building distribution system. Raising a pad or locating a room on another level can add structural, routing and handling constraints. Engineering teams should coordinate these interfaces rather than treating elevation as an isolated switchgear dimension.

Design drainage without creating new exposure

Drainage planning should account for the area immediately around the equipment and the route water may take after a heavy storm. Review surface slope, nearby drains, sump arrangements, discharge points and the possibility of blocked inlets or power loss affecting pumps. Do not assume a drain will prevent flooding unless the civil design establishes its capacity, discharge conditions and maintenance plan.

Keep water-control measures compatible with equipment access and future work. Berms, curbs and barriers may impede door swing, egress, lifting or maintenance access if their location is not coordinated. Sealing building penetrations and managing trench or conduit pathways can also influence installation scope. Have the responsible design professionals define the flood-protection approach and verify its effect on the complete electrical room or outdoor installation.

Treat replacement risk as a location criterion

Flood exposure can turn a location decision into a long-term outage and replacement problem. Consider what water intrusion could affect beyond the switchgear, including upstream and downstream distribution, control wiring, protective devices and connected building services. A higher or more protected location may reduce exposure, but it can also lengthen feeders, complicate routing or require structural changes. Compare these tradeoffs with the facility’s restoration priorities.

Plan how damaged equipment would be removed and replaced if access is limited after a flood. Review equipment transport paths, door openings, lifting provisions, temporary staging, roadway access and the possibility that surrounding areas remain wet or obstructed. These constraints can influence room arrangement and the configuration selected for a new assembly. The project team should document an achievable replacement route, not only a preferred operating location.

Give procurement a usable design package

For a quote, provide the equipment type and electrical requirements, one-line diagram, lineup arrangement, indoor or outdoor location, target delivery point, and the project’s elevation criteria. Include the elevation datum, finished-floor or pad elevation, flood basis, relevant site drawings, access limits, environmental conditions and known drainage constraints. Identify which details are preliminary and which are approved, so open interfaces can be resolved before the order is finalized.

Also clarify whether the specification calls for UL 891 switchboard assemblies; that standard applies to switchboards and does not establish a blanket listing for medium- or high-voltage switchgear. State the required configuration, connection orientation, cable-entry needs and any project-specific documentation expectations. Exact scope, availability and timeline are confirmed for each order. American-made components, custom-built configurations, short lead times and nationwide shipping may support project planning, subject to the requirements and details of the specific order.

Coordinate the Georgia delivery handoff

Georgia sites can face different combinations of coastal, river, low-lying urban or intense-rainfall exposure. Provide the project address or delivery location, receiving constraints, site access instructions and planned installation sequence when requesting a quote. Delivery planning should account for whether a truck can reach the unloading area under expected site conditions and whether equipment must be staged before the room or pad is ready.

Before release, align the equipment drawings and shipping plan with the current site layout, elevation decisions and civil work. Confirm who will review foundation and anchorage details, cable routes, water-control measures and installation clearances. Assign an engineering owner for unresolved flood assumptions and record the approved elevation basis in the project package. This gives procurement and the installation team a clear handoff and helps prevent a late location change from becoming an equipment replacement problem.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote