New electrical distribution equipment, built around your projectServing Georgia
Row of gray electrical control cabinets with switches and indicator lights.

Design

Switchgear Cable Bending Space

For engineers, electrical contractors and facilities teams in Georgia, cable bending space is a layout decision that affects enclosure dimensions, lug placement and field installation. Share conductor details and the intended cable entry and exit paths early so the switchgear design can account for termination geometry and the room needed to install conductors without forcing tight bends.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Start with the actual conductors

Cable space cannot be set from ampacity alone. Conductor material, insulation type, voltage class, size, number of parallel conductors per phase and grounding arrangement all influence the diameter and handling needs of the cables. A conductor schedule is more useful than a single feeder rating because it shows how many cables must reach each termination and whether the largest conductors land in one section or are distributed across the lineup.

Provide the planned cable sizes and quantities, including neutral and equipment grounding conductors, along with any known cable manufacturer or insulation details. If final conductor selection is pending, identify the design basis and the range still under consideration. The manufacturer can then review the proposed arrangement, but final space requirements depend on the selected equipment, terminals and applicable installation rules.

Check minimum bend requirements

The minimum bending radius is determined by the conductor or cable construction and its applicable installation requirements; it is not a universal distance that can be applied to every switchgear section. The cable must transition from its entry point to the terminal while respecting that limit. A larger conductor, stiff insulation or multiple parallel sets can require more room than a compact layout appears to provide on a single-line diagram.

Engineers should compare the cable manufacturer’s bending guidance with the planned route, including the point where the cable turns and the distance from that turn to the lug. Confirm whether conductors approach from above or below and whether the entry path includes bends outside the enclosure. Avoid treating enclosure depth or a general clearance dimension as proof that the actual cable can be routed and terminated as intended.

Coordinate termination positions

Termination position determines how cable space is used. Lugs may be arranged for top or bottom entry, and their orientation, phase spacing and mounting location affect the route each conductor must follow. Multiple conductors per phase need room to fan out and reach their assigned terminals without crossing in ways that obstruct other terminations. Neutral and ground landing locations also need to be included in the layout.

For each feeder or main connection, provide the equipment section, entry direction, conductor count and intended terminal arrangement. Identify whether the project requires compression lugs, mechanical lugs or another specified termination approach, and provide terminal submittal requirements when available. Do not assume a preferred lug position can be accommodated without checking the complete section layout and the selected equipment configuration.

Include installation and service access

Adequate internal bending room does not guarantee that installers can reach the cable entry, pull conductors into position or work at the terminations. Consider the route from the raceway or cable tray to the switchgear, the location of nearby walls and other equipment, and the space needed for pulling and dressing conductors. Removable barriers, covers and access panels may affect the sequence of work and should be considered in the installation plan.

Show the switchgear lineup in relation to the room, cable trenches, overhead pathways and adjacent obstructions. Note which side or sides must remain accessible during installation and whether conductors enter through the top, bottom or another planned opening. The electrical contractor should verify the field route and working conditions; layout review should not substitute for applicable installation requirements or project-specific engineering.

Resolve constraints before release

When cable sizes, entry locations or termination details change late, the required section arrangement or enclosure dimensions may also need review. Check these interfaces before approving drawings for manufacture, especially where a lineup has limited room, large parallel conductors or several feeders entering the same area. If a clash appears, evaluate the route, terminal arrangement and enclosure configuration together rather than shortening a bend without confirming the cable requirements.

For a quote, share the one-line diagram, preliminary or final conductor schedule, entry direction, cable pathway drawings, room layout and terminal specifications available at the time. Mark unresolved items clearly, including future feeders or alternate conductor sizes. We build new switchgear and custom configurations in the United States; the applicable scope, availability and timeline are confirmed for each order.

Handoff for Georgia projects

A useful design handoff ties each cable schedule entry to a specific switchgear section and termination point. Include the latest equipment layout, entry openings, conductor quantities and access constraints in the same review package. This gives the project team a basis to coordinate raceways and cable paths with the equipment design and reduces the risk of discovering a bend or access conflict during installation.

For Georgia delivery, coordinate the receiving location, site access, unloading plan and required delivery sequence with the project schedule. Nationwide shipping is available, while delivery details and timing are confirmed for the order. Before drawing approval, reconcile conductor data with the actual route and terminal positions, then identify any remaining assumptions for engineering review.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote