New electrical distribution equipment, built around your projectServing Georgia
Gray switchgear cabinets with breaker controls beside exposed conduit and fittings.

Industry Solutions

Power Plant Auxiliary Power Distribution

Generation facilities depend on station-service power for controls, pumps, fans, cooling systems, fuel handling and other auxiliary loads. A well-defined distribution package must account for normal and alternate sources, transformer connections, fault protection and operating sequences. We build new switchgear and UL 891 switchboard assemblies to project requirements, with scope and delivery coordinated for Georgia sites.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Map the station-service loads

Start with the equipment that must remain available during startup, normal generation, shutdown and loss of a preferred source. Load schedules should distinguish continuous, intermittent and standby duties, and identify motors, variable-frequency drives, heaters, control power and sensitive electronics. Motor starting and simultaneous operating scenarios can shape transformer selection, bus sizing and protective-device coordination.

For each load group, clarify voltage, phase, frequency, full-load current, starting method and required source. Identify essential loads and any permitted load-shedding sequence rather than treating every feeder as equally critical. These details let the design team establish a distribution arrangement that supports the plant’s operating philosophy without assuming a particular generator or auxiliary system configuration.

Define transformer interfaces

Station-service power may come from a unit auxiliary transformer, a station-service transformer connected to the grid, or another plant-defined arrangement. Provide one-line diagrams and transformer data, including primary and secondary voltages, impedance, grounding method, available fault current and connection details. Confirm whether the switchgear scope includes incoming compartments, transition sections, metering provisions or only downstream distribution.

Interface planning also covers cable or busway entry, phase orientation, termination space, neutral and ground connections, and physical clearances. Establish which party supplies transformer protection, instrument transformers, surge devices and interconnecting conductors. Resolving these boundaries early helps avoid mismatched equipment and late changes to enclosure dimensions or feeder layouts.

Plan normal and backup sources

A plant may use a second transformer, an emergency generator, an independent utility feed or a combination of sources. The intended transfer method matters: specify whether transfer is manual or automatic, open transition or another engineered sequence, and which loads transfer. Include control-power source, permissives, interlocks, bypass needs and the behavior expected when a source returns or becomes unstable.

Backup capacity should be evaluated against the actual emergency load list, motor-starting duty and operating duration required by the plant’s design. Clarify whether the generator is dedicated to station service or serves additional loads, and whether nonessential feeders must drop before transfer. These are engineering decisions; equipment configuration should follow approved system studies and the facility’s operating requirements.

Coordinate protection and operating access

Protection depends on the source characteristics and system study, not on a generic breaker selection. Share available fault-current values at each incoming point, transformer impedance, grounding details, feeder loads and coordination requirements. Engineers can use this information to specify breaker functions, trip settings, bus protection interfaces and selective coordination objectives appropriate to the system.

Operating procedures influence the lineup as much as electrical ratings. Identify required metering, status indication, remote monitoring points, control circuits, drawout needs, maintenance access and any planned future feeders. Confirm environmental conditions, room access, seismic or other project criteria when applicable. Final ratings, protection settings and installation requirements need review by the responsible engineer and authority having jurisdiction.

Shape the equipment package

A custom-built package can organize incoming sources, bus sections, tie breakers and outgoing auxiliary feeders around the plant’s one-line and room layout. For low-voltage switchboard assemblies, UL 891 is the applicable switchboard standard; it does not establish a blanket listing for medium- or high-voltage switchgear. State the equipment class and scope clearly so submittals address the right assembly and interfaces.

For a quote, provide the latest one-line, load and feeder schedules, transformer and source data, protection-study requirements, control schematics, site conditions, preferred lineup dimensions and required submittal documents. Note alternates, spare provisions, future expansion and any owner-furnished components. We confirm exact scope, component availability and schedule for each order rather than assuming standard ratings or stock.

Coordinate Georgia delivery and handoff

Georgia projects benefit from resolving shipment and receiving constraints while the lineup is being configured. Share the delivery location, access route, unloading capability, indoor storage conditions, receiving hours and any restrictions on truck size or equipment sections. Nationwide shipping can support Georgia destinations, with routing and shipment timing confirmed for the specific order and site requirements.

Before release, align approved drawings, interface responsibilities, labeling and the documentation needed for installation and commissioning. Confirm who provides field terminations, settings, testing and energization, and ensure qualified personnel perform that work under the project’s approved procedures. For a practical next step, send the station-service one-line, load schedule, source and transformer information, and Georgia delivery constraints for configuration review.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote