New electrical distribution equipment, built around your projectServing Georgia
Gray switchgear cabinets with breaker controls beside exposed conduit and fittings.

Products

Electrical Busway Systems

Busway can distribute power through a building with compact, modular runs, but the connection to a switchboard or switchgear must be engineered as part of the system. For Georgia engineers, contractors and purchasing teams, the key is to coordinate electrical ratings, physical interfaces, routing and project timing before equipment is released for fabrication.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Where busway fits in a distribution plan

Busway, also called bus duct, carries power in an enclosed assembly of bus bars and insulating supports. Straight sections, fittings and tap-off provisions can create a defined distribution path through a facility. Compared with multiple parallel cable runs, it may simplify routing where loads are concentrated along a corridor, floor or production area. The right choice depends on the building layout, load pattern, available space and installation method.

A busway run is not a standalone substitute for system design. Engineers need to establish its role between the source, distribution equipment and downstream loads, including how protective devices and disconnects are arranged. Identify whether the run serves a feeder, riser or load distribution purpose, and whether planned future loads or branches affect its configuration. These decisions shape both the switchboard connection and the busway sections to be specified.

Define electrical requirements first

For a quotation, provide the system voltage and frequency, phase and wire arrangement, grounding approach, and the required ampacity. Share the available fault-current information and the protective-device details used in the system design. Busway interrupting or short-circuit withstand characteristics, as applicable to the selected product, must be coordinated with the source and protection. A busway’s rating cannot be selected from load current alone.

Clarify the environment and operating conditions along the route. Indoor or outdoor exposure, ambient temperature, moisture, dust, corrosive conditions and installation orientation can influence enclosure and product selection. State whether the busway is intended for feeder service or includes plug-in provisions for tap-off units. Final ratings and configuration depend on engineering review and the specific manufacturer’s product data.

Check the switchboard interface

The connection between busway and a switchboard needs a defined mechanical and electrical interface. Confirm the equipment manufacturer and model, main bus arrangement, connection location, bus material, phase sequence and neutral and ground provisions. Connection orientation, enclosure dimensions, access clearances and the direction of the busway approach also matter. A drawing or verified dimensional information is more useful than assuming that equipment with matching voltage and ampacity will connect directly.

Review whether the switchboard is designed with a suitable busway connection section or requires a separately engineered transition. The transition must account for alignment, support, enclosure openings, barriers and access for installation and inspection. UL 891 applies to switchboard assemblies, not as a blanket certification for busway or medium- and high-voltage switchgear. Confirm the applicable product standards and documentation for each component and assembly.

Coordinate switchgear and protection

When busway connects to switchgear, verify the switchgear’s voltage class, bus configuration, terminal arrangement and available connection space. Do not assume that low-voltage switchboard connection details apply to medium-voltage equipment. The design team must establish the appropriate interface and protection scheme for the specific system. Drawings, manufacturer data and engineering review should resolve conductor arrangement, clearances, grounding and any required transition equipment.

Protection coordination should consider the source device, busway characteristics and downstream devices together. Share the one-line diagram, fault-current study information and protective-device selections when available. The engineer of record and relevant equipment manufacturers can determine whether the proposed combination is suitable. No rating, connection method or code compliance should be inferred from a general busway description; the project documents and authority having jurisdiction govern.

Route, supports and installation planning

Busway dimensions and fittings must follow the actual route, not a conceptual straight line. Provide floor-to-floor elevations, route lengths, turns, offsets, penetrations, equipment-room layouts and obstructions. Identify the mounting orientation, support locations, access zones and any areas where future expansion is expected. The installation team should verify field dimensions and coordinate building conditions before fabrication, especially at transitions and constrained equipment rooms.

Plan for shipping sections, staging and movement into the building as well as final access for assembly. Georgia delivery can be coordinated around the project’s receiving location, construction sequence and site access requirements; route, packaging and timing are confirmed for each order. Confirm who is responsible for field verification, installation, connection and inspection, and ensure qualified personnel perform electrical work under the project’s approved documents.

Prepare a complete quotation handoff

A useful quote request includes the one-line diagram, equipment schedules, busway route drawings, electrical ratings, switchboard or switchgear information, connection dimensions and required tap-off locations. Also state the project location in Georgia, requested delivery window, receiving constraints and whether drawings or submittals are needed for review. Identify any owner or engineer specifications that affect materials, enclosure, labeling or documentation.

Before release, reconcile the approved drawings with the equipment connection point, busway layout, ratings and delivery sequence. Assign responsibility for resolving open dimensions and design questions, then document the accepted configuration and scope. Send the one-line, route plan, equipment model details and target schedule with the quote request so the busway and its switchboard or switchgear interface can be evaluated together.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote