New electrical distribution equipment, built around your projectServing Georgia
Gray electrical switchgear cabinets on wooden pallets, with a front door open.

Protection

Circuit Breaker Protection Functions

Circuit-breaker trip functions determine how protection responds to overloads, short circuits and other measured conditions. For engineers, contractors and facility teams specifying new switchgear in Georgia, the key is matching each function and setting to the equipment, system study assumptions and operating needs—not choosing settings from a generic table. This guide outlines the decisions to document before procurement.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Start with the protected equipment

A breaker’s protection package should reflect what it protects and where it sits in the distribution system. A feeder breaker, transformer secondary breaker and main device may face different load profiles, fault-current exposure and coordination requirements. Identify the circuit purpose, connected equipment, normal and peak loads, conductor information, system voltage and available fault-current basis used by the project engineer.

Also clarify whether the device is intended to provide overload protection, short-circuit protection, ground-fault protection, or a defined combination. The breaker frame and trip unit must be suitable for the application, but a larger frame or broader feature set does not by itself establish a correct protective scheme. Final selection depends on engineering review of the complete system and applicable project requirements.

Know the common trip functions

Long-time pickup and delay address sustained overcurrent. Pickup establishes the current threshold for the long-time response, while delay shapes how long the breaker tolerates an overload before tripping. These choices must account for expected loading and the protected conductors or equipment, while avoiding unnecessary interruptions during legitimate operating conditions.

Short-time pickup and delay, when provided, shape response to higher overcurrents and can support coordination between upstream and downstream devices. Instantaneous protection responds without an intentional time delay once its operating threshold is reached. Ground-fault protection detects qualifying ground-fault current in applicable systems. Function availability, adjustment range and behavior vary by trip unit, so specifications should name the required functions rather than assume every breaker includes them.

Select settings from study inputs

Protection settings should follow the approved coordination and short-circuit study, along with equipment and conductor limits. Relevant assumptions can include utility or source characteristics, transformer impedance, conductor lengths and sizes, motor contribution, operating configurations and the fault-current values at each device. If these inputs change after the study, settings may need review; an old schedule should not be treated as automatically valid for a revised system.

The study should identify proposed pickups and delays, the basis for selective coordination where required, and any constraints such as equipment withstand limits or minimum fault current. Ask who will provide the final settings and who will verify them against the selected trip-unit capabilities. A manufacturer can build to a documented configuration, but should not substitute an unreviewed default for the project engineer’s protection decisions.

Check coordination and operating constraints

Coordination is not achieved simply by setting an upstream breaker slower than a downstream breaker. Time-current curves, device tolerances, fault-current levels and the full range of expected system configurations affect whether a fault is isolated as intended. Review both high-current and lower-current conditions, and consider how alternate sources or tie arrangements change the available current and device relationships.

Operational needs matter as well. A facility may need to consider nuisance-trip exposure, continuity of critical loads, maintenance practices and any specified arc-energy reduction or maintenance mode features. Those features are application-dependent and do not replace the required study or operating procedures. Confirm that requested functions and adjustment ranges are available in the proposed device and compatible with the intended control and commissioning plan.

Specify the configuration and handoff

For a quote, provide the one-line diagram, equipment schedule, breaker location and role, required frame and trip-unit information if established, and the latest approved protection settings or study requirements. Include system voltage, source and transformer data, expected load, fault-current basis, special functions, control or indication needs, and any project specifications governing the assembly. Identify which items remain pending engineering so the proposal does not imply an unconfirmed setting.

Before release, reconcile the breaker schedule, trip-unit features, settings document and switchboard drawings. Agree on who supplies setting files or values, who reviews them, and what records are required at handoff. For a UL 891 switchboard assembly, UL 891 applies to the switchboard standard; it does not establish that a particular protection study or breaker setting is suitable for the installation.

Plan delivery around the project

For Georgia projects, align the requested configuration and delivery window with drawing approval, study completion, site readiness and installation sequencing. We build new switchgear with custom configurations and American-made components, and ship nationwide; exact scope, component availability and timing are confirmed for each order. Share the destination, receiving constraints and milestone dates early so procurement can evaluate the requested build and delivery plan.

Before procurement is finalized, send the current one-line diagram, breaker schedule, study status and required trip functions, then flag every unresolved setting or system assumption. Ask for confirmation that the proposed breaker configuration matches the documented requirements, and route final settings through the responsible engineer for approval. This focused handoff helps keep the equipment specification tied to the protection design rather than to an assumed generic setup.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote