New electrical distribution equipment, built around your projectServing Georgia
Flatbed truck carrying gray electrical cabinets outdoors.

Testing

Battery Charger and DC Control Power Tests

Reliable DC control power supports breaker operation, protection, annunciation, and other functions that may be needed during an AC supply interruption. For Georgia engineers, contractors, and facilities teams, testing should establish what the charger and battery can deliver, confirm alarm behavior, and trace the results through the equipment that depends on them.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Define the DC system under test

Start by identifying the DC voltage, charger arrangement, battery type, nominal capacity, and the loads served. The scope may include a switchboard or switchgear control circuit, trip and close circuits, protective relays, indication, communications, or auxiliary equipment. Drawings and equipment schedules help distinguish essential loads from functions that can be isolated for testing.

Clarify whether the work is a factory test of a new assembly, an acceptance test at the project site, or a periodic evaluation of an operating system. These scopes have different access, outage, and documentation needs. Share the applicable drawings, control schematics, battery and charger data, specified test procedures, and any project acceptance criteria before defining the test plan.

Verify charger output and operating modes

A charger check should address output voltage and current under the operating conditions specified for the project, along with float and equalize settings where applicable to the battery design. Review AC input requirements, output regulation, current limiting, and the effect of connected DC loads. Record instrument details and actual readings so results can be compared with approved equipment data and project limits.

Confirm how the charger behaves when AC input is lost or restored, and whether it transfers between operating modes as intended. A test plan should account for charger redundancy, remote sensing, temperature compensation, or parallel operation only when those features are part of the supplied design. Do not assume a setting from another installation applies; engineering must establish the correct values for this system.

Assess battery condition and capacity

Battery condition is more than a charger voltage reading. Depending on battery chemistry and the approved procedure, evaluation may include visual inspection, terminal and intercell connection checks, temperature, cell or block voltage, and a capacity or discharge test. The selected method should follow the battery manufacturer's instructions and project requirements, with suitable precautions for the battery type and installation.

Capacity testing can require isolation or carefully managed load control, and the test duration and acceptance threshold depend on the design basis. Confirm whether the project needs a full capacity test, a condition assessment, or baseline measurements for future comparison. Share battery model, age, prior test records, rated capacity, expected duty cycle, and known deficiencies when requesting a scope.

Prove alarms and dependent functions

Test the specified charger and battery alarms, such as AC input failure, charger failure, DC undervoltage, ground detection, or battery trouble, when those indications are provided. Verify local annunciation and any remote status or alarm interface included in the design. Record the initiating condition, displayed point, relay or communication response, and reset behavior rather than treating an alarm lamp alone as proof.

Trace DC power into the functions it supports. Depending on the approved scope, this may include breaker trip and close circuits, protective relay operation, control switches, status indication, or supervisory interfaces. Functional checks should use controlled procedures and qualified personnel, with equipment in an approved test condition. Confirm in advance which devices can be operated and which require simulation or isolation.

Set scope, access, and acceptance criteria

Before work begins, resolve outage windows, switching responsibilities, access restrictions, test points, load connections, and the treatment of active protection and alarms. The owner or engineer should identify hazards and establish the approved safety and operating procedures. Testing must not compromise critical loads or leave a protective function unavailable without authorization and compensating measures.

For a manufacturer quote, provide the project location in Georgia, equipment drawings, DC system and battery data, test objective, quantity and configuration, required witness points, acceptance criteria, and requested report format. Identify whether testing is for a new custom-built assembly or existing project equipment, and state site access and schedule constraints. Scope, availability, and timing are confirmed for each order.

Document results and project handoff

A useful report links each measurement and functional result to its test point, device, procedure, and acceptance limit. Include relevant charger settings, battery readings, alarm responses, exceptions, corrective actions, and any deferred tests. Note conditions that affect interpretation, such as connected loads or a limited test window, so the record can support commissioning and later maintenance decisions.

For Georgia projects, delivery planning should align the tested equipment and its records with site receiving, installation sequencing, and the approved commissioning schedule. Nationwide shipping can be arranged for new equipment, while exact configuration and delivery timing are confirmed for each order. Before handoff, reconcile test records against the final drawings and identify unresolved items; then have the responsible engineer approve the system for its intended service.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote