New electrical distribution equipment, built around your projectServing Georgia
Three gray electrical switchgear cabinets on pallets, with a door swung open.

Fabrication

Switchgear Quality Inspection Points

For engineers, contractors, facilities teams, and procurement managers in Georgia, inspection planning should follow the equipment from approved documents through final release. Clear gates help catch material substitutions, dimensional errors, wiring discrepancies, and missing records while corrections are still practical. This guide outlines what to verify and what project information to settle before requesting a quote.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Set inspection criteria before fabrication

Begin with the approved one-line diagram, equipment schedule, specifications, and required submittals. Confirm system voltage, phase, frequency, bus arrangement, interrupting and withstand requirements, enclosure details, incoming and outgoing provisions, metering, protective devices, and control options. Record the governing project documents and revision dates so production and inspection use the same design basis.

Agree on hold points and acceptance records before work starts. Ask which checks will be documented at material receipt, after fabrication, during wiring, and at final inspection, and whether the project requires witness opportunities or specific forms. Inspection cannot resolve an unclear specification; identify open items, deviations, and approval responsibility before they become fabrication assumptions.

Verify materials and traceability

At receiving, compare parts against the approved bill of material and purchasing records. Check manufacturer and catalog identifiers where specified, quantities, ratings, accessories, and visible condition. Inspect bus stock, supports, insulating materials, conductors, lugs, breakers, instruments, and control components for damage, contamination, or mismatched options. A nameplate or package label should not substitute for checking the actual component against the design.

For substitutions, confirm that the proposed part matches required electrical and mechanical characteristics and obtain the appropriate engineering approval before installation. Track identifying information and revision status in a way that links installed components to records. If a specified component is unavailable, raise the issue early: a change can affect bus connections, mounting, wiring diagrams, procurement timing, and customer approvals, not just the parts list.

Inspect enclosure and bus fabrication

Check enclosure dimensions, section layout, access, mounting features, openings, barriers, and finish against approved drawings. Verify that cutouts and knockouts are in the intended locations and do not compromise required clearances or interfere with devices. Inspect formed edges, seams, fasteners, and grounding provisions for workmanship and consistency with the specified construction. Confirm shipping splits and joining details where the assembly must be transported in sections.

Bus inspection should address material and size specified by the design, joint surfaces, alignment, supports, clearances, and phase identification. Review connection hardware and joint preparation against the applicable manufacturing instructions and project requirements. Torque values are design- and component-dependent; use the approved procedure and calibrated tools, then record results where required. Any field joining or adjustment should be defined in the handoff documents rather than left to assumption.

Check wiring against released drawings

Compare control and metering wiring with the latest approved elementary diagrams, point-to-point schedules, and terminal plans. Confirm wire identification at both ends, terminal numbers, conductor type and routing as specified, polarity, and separation requirements. Check that device contacts, coils, transformers, meters, and protective relays are connected to the intended terminals and that unused conductors are handled as documented.

Inspect workmanship for secure terminations, supported conductors, protection from sharp edges, suitable bend paths, and access for maintenance. Verify control-power sources, fuses, interlocks, and customer interface terminals against the design. Where a project includes communications or remote signals, confirm protocol, addressing responsibilities, and required interface points. Record drawing discrepancies and resolve them through controlled revisions, not undocumented field edits.

Review assembly and test evidence

During assembly, verify device orientation, compartment arrangement, barriers, labels, and mechanical operation against the approved configuration. Check that doors and covers fit, hardware is complete, and specified interlocks operate as intended. Confirm nameplate data and warning labels match the released documents. A visual check can reveal assembly problems, but it does not replace the tests required by the applicable product standard, specification, or approved quality plan.

Define the final test scope for the actual equipment and contract. Depending on design and requirements, records may include continuity checks, insulation-resistance tests, control-circuit functional checks, instrument or relay verification, and mechanical operation checks. UL 891 applies to switchboard assemblies; it is not a blanket listing for medium- or high-voltage switchgear. Confirm the assembly type, applicable requirements, and documentation with the manufacturer and project engineering team.

Close records and prepare Georgia delivery

Before release, reconcile the equipment identification, approved drawing revisions, material records, inspection findings, test results, and any approved deviations. Identify unresolved items, their disposition, and who must accept them. The turnover package should make it possible for the receiving and installation teams to understand section arrangement, shipping splits, lifting and handling instructions, field connections, and documents that govern installation. Qualified personnel and the project authority determine installation and acceptance requirements.

For a quote, share the one-line diagram, equipment schedule, specifications, required standards, drawings, delivery location in Georgia, site access constraints, requested ship date, and inspection or witness requirements. State whether the project needs customer-approved submittals before fabrication and which records are required at handoff. Confirm scope, component availability, and schedule for the specific order; then use the agreed inspection gates and document list as the release checklist for delivery.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote