New electrical distribution equipment, built around your projectServing Georgia
Row of gray electrical control cabinets with switches and indicator lights.

Testing

Switchgear Contact Resistance Testing

Contact resistance measurements help engineers assess the condition of bolted joints, bus connections and other current-carrying interfaces in switchgear. Results are useful only when the test method, equipment state and comparison basis are clear. This guide explains what to measure, how to interpret readings responsibly, and what information to provide when planning new switchgear for a Georgia project.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

What the measurement can reveal

A contact resistance test measures the small electrical resistance across a defined connection, typically using a micro-ohmmeter and a high-current test method. Elevated or changing resistance can indicate a connection that deserves investigation, such as a joint affected by contamination, surface condition, inadequate contact pressure or mechanical movement. A reading is an assessment point, not a complete diagnosis of the cause.

The value matters because resistance at a current-carrying interface can contribute to localized heating under load. The measurement does not, by itself, establish operating temperature, fault-current withstand, or overall equipment condition. Engineers interpret it alongside the connection design, rated current, inspection findings, loading history and applicable manufacturer guidance.

Define the test point and equipment state

Before specifying a test, identify the exact boundaries of each measurement. A reading across a breaker pole, a bus splice, a disconnect contact or a bolted bus joint represents a different combination of interfaces. Drawings or a marked single-line diagram can help the test team locate consistent points and avoid comparing unlike connections.

State whether testing is planned on a new assembly, during commissioning, or as part of maintenance or troubleshooting. Equipment may need to be isolated, de-energized and prepared under the applicable site procedures by qualified personnel. The test plan should define switching position, accessible test points and any required disassembly; access limitations can affect the method and scope.

Choose a repeatable measurement method

A four-wire Kelvin method separates the current connections from the voltage-sensing connections, reducing the influence of test-lead resistance. The selected instrument and test current should suit the component and the applicable procedure. Probe placement, surface access, connection cleanliness, contact pressure and instrument condition can all affect repeatability, so the procedure should document how each reading is taken.

Avoid treating a single number as a universal pass-or-fail limit. Acceptance criteria may come from equipment documentation, project specifications, applicable standards or an engineer-approved baseline. Record instrument identification and calibration status, test current, measured value, measurement points, equipment temperature where relevant, and unusual conditions. Consistent records make later comparisons more meaningful.

Compare readings with context

Comparison is strongest when readings come from equivalent phases, poles or joints tested with the same setup and comparable conditions. A phase-to-phase difference can flag an outlier for review, while a trend over time may show a connection changing. Neither observation proves a defect without considering measurement uncertainty, equipment construction and the history of the specific connection.

If a result is unexpectedly high or inconsistent, first verify the test setup and repeat the measurement using the documented method. Qualified personnel and the responsible engineer can then determine whether inspection, torque verification, cleaning, repair or further evaluation is appropriate. Do not loosen or retighten a joint solely to improve a reading; follow the equipment instructions and approved work controls.

Specify the scope for new switchgear

For a new switchboard or switchgear order, clarify whether resistance testing is a required factory test, a field commissioning activity, or both. Identify the assemblies and connections to be measured, the requested method, reporting format, witness requirements and acceptance basis. Confirm what is included in the proposed scope rather than assuming every connection or device will receive an individual measurement.

Share the one-line diagram, equipment type, voltage and current ratings, device list, connection details, project specification and intended test stage when requesting a quote. Also note access, schedule, documentation and site coordination needs. These details help establish a practical scope without assuming that one test procedure fits every assembly.

Plan records and Georgia delivery

A useful handoff includes a connection-by-connection results table, clear point identifiers, test conditions, instrument details and any exceptions or retests. Tie identifiers to the final drawings so commissioning and maintenance teams can locate the measured interfaces later. For a new custom-built configuration, confirm which records and test activities are part of the order before release.

Georgia delivery can be coordinated with the project’s receiving plan, installation sequence and test schedule; shipping arrangements and timing are confirmed for each order. When requesting pricing, provide the delivery location, required-on-site date, unloading constraints and whether testing documentation is needed with the assembly. Next, send the drawings and requested measurement scope for review so engineering and procurement can align the method, acceptance basis and handoff.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote