New electrical distribution equipment, built around your projectServing Georgia
Flatbed truck carrying gray electrical cabinets outdoors.

Protection

Feeder Overcurrent Protection

For Georgia engineers, contractors, facility teams, and purchasing managers, feeder overcurrent protection starts with matching a protective device to the conductors and the load it serves. It also depends on available fault current, upstream and downstream devices, and the switchboard configuration. Share these details early so the equipment scope can be reviewed against the project design.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Start with the feeder and its load

A feeder device must be selected in relation to the feeder conductors, the calculated load, and the conditions of use. The design team establishes conductor ampacity after accounting for applicable correction and adjustment factors, termination temperature limits, installation method, and other project conditions. The device rating and permitted settings must then be evaluated against those limits and the governing electrical requirements.

Provide the nominal system voltage, phase and wire arrangement, feeder load, conductor material and size, insulation, parallel-conductor details, and intended load profile. Identify continuous loads, motors, transformers, nonlinear loads, and any equipment with significant starting or inrush current. These details help distinguish normal operating current from conditions that protection must interrupt, without assuming a device rating from load amperes alone.

Match the protection method to the application

Feeder protection may use a circuit breaker or a fusible arrangement, depending on the design, required functions, coordination objectives, available space, and operating practices. Breakers can offer adjustable trip functions when the selected device supports them; fuses have time-current characteristics that vary by type and rating. Neither approach is automatically preferable. The engineer should define the required trip functions, setting ranges, interrupting capability, and any monitoring or indication needs.

Ask whether the design calls for long-time, short-time, instantaneous, or ground-fault functions, and identify which functions are required by the engineered scheme and applicable rules. Settings and device features should be selected for the actual application, not assumed from a generic switchboard description. The final selection must reflect the equipment manufacturer's published data and be reviewed by the responsible electrical engineer.

Check fault duty and device capability

Available fault current at the feeder location affects the required interrupting capability of the protective device and the short-circuit rating of the assembly. Request the project's fault-current study or the utility and system information needed to complete one. Include transformer ratings and impedance, conductor lengths, upstream source details, and any generator or other source that can contribute fault current. Changes to these inputs can change the calculated duty.

Confirm that the proposed device and switchboard ratings are suitable for the calculated conditions and the intended system configuration. A series rating, where considered, requires specific listed combinations and engineering verification; it should not be presumed from component ratings alone. UL 891 applies to switchboard assemblies and does not establish a blanket listing for medium- or high-voltage switchgear. Scope and ratings must be confirmed for the equipment being specified.

Coordinate upstream and downstream devices

Coordination aims to limit the portion of a system interrupted by a fault, while maintaining protection for conductors and equipment. It requires comparing time-current characteristics for the feeder device, upstream protection, and downstream branch or equipment devices across relevant fault-current ranges. A desired coordination interval or selective-coordination requirement should be identified by the design team and evaluated against manufacturer data.

Do not select a slower trip setting solely to improve coordination if it compromises conductor or equipment protection. Short-circuit and ground-fault conditions can behave differently from overloads, and instantaneous elements may affect selectivity. Provide the latest coordination study, device models or existing device information, and the project's protection criteria. Where study results depend on a specific device or setting, record that basis in the submittal and commissioning documents.

Define the switchboard and project interface

For a new UL 891 switchboard assembly, specify the feeder device location, number of feeders, bus arrangement, incoming source, enclosure and installation conditions, and required metering or control interfaces. Identify available section space and any constraints for cable entry, termination access, or future feeders. Provide drawings and schedules where available; physical layout and device selection must be reviewed together rather than treated as independent decisions.

For a quote, share the one-line diagram, panel or feeder schedule, load and conductor data, fault-current information, coordination requirements, preferred protective-device approach, and requested submittal scope. Note what is preliminary and what is approved for construction. Exact configuration, component availability, and timeline are confirmed for each order, so unresolved study values or design changes should be clearly identified before release.

Plan delivery and closeout around the design

Georgia projects benefit from resolving protection inputs before manufacturing and delivery are scheduled. Confirm the ship-to location, site access and receiving constraints, required delivery window, and whether the equipment must arrive with particular documents or identification. Nationwide shipping can support Georgia project delivery, but route, timing, and order scope are confirmed for the specific project rather than assumed from a general schedule.

Before requesting a quote, assemble the latest one-line, feeder schedule, conductor information, fault study, and coordination criteria, then flag any pending engineering decisions. After equipment selection, reconcile device catalog data and settings with the approved studies and project documents. This gives the engineer and procurement team a clear basis to review feeder protection, confirm the switchboard scope, and hand off the order for project-specific configuration.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote