Confirm the system voltage and insulation basis
Provide the nominal system voltage, highest voltage for equipment, frequency, grounding method, and expected operating range. A 15-kV-class designation does not, by itself, establish the correct insulation level or prove suitability for a particular system. Confirm the specified withstand requirements for power-frequency and impulse conditions against the project’s design criteria and applicable standards.
Describe the installation environment as well as the one-line diagram. Indoor or outdoor location, altitude, ambient temperature, humidity, contamination, and exposure to moisture or corrosive conditions can affect equipment selection. Identify cable entry direction, phase arrangement, clearances, and available room dimensions. Engineering review should resolve the insulation coordination and application before the specification is finalized.
Define interrupting and short-time duty
The breaker’s interrupting rating must be evaluated against the maximum available fault current at its location, including relevant utility and on-site generation contributions. Share the utility fault-current data, transformer impedance and ratings, conductor information, and any expected operating configurations. If values differ by source or operating mode, document each condition rather than relying on one assumed fault level.
Interrupting capability is only one part of the duty. Specify the required short-time withstand current and duration, close-and-latch capability, and switching duties where the study or operating plan makes them relevant. Identify the system X/R ratio or other study assumptions when available. Do not select a rating from nominal voltage or breaker frame alone; coordinate ratings with the system study and equipment design.
Specify protection and control functions
List the protection functions required for each circuit and the equipment they protect. Depending on the application, the design may call for phase and ground overcurrent, transformer protection, bus protection, or other functions determined by the protection study. Provide relay requirements, CT ratios and accuracy needs, voltage sensing details, trip and close control voltage, and any preferred communications protocol or monitoring interface.
Clarify how protection settings will be developed, reviewed, and applied. Share coordination-study assumptions, existing device information, and any required interlocking or transfer logic. Distinguish functions required at initial energization from provisions for future expansion. The manufacturer can use this information to define a proposed arrangement, but protection coordination, settings, and system adequacy remain subject to qualified engineering review and the project’s approval process.
Resolve the physical and operating configuration
Describe the lineup’s circuit count, source arrangement, bus requirements, metering, utility interface, and desired future spaces. State whether the project requires drawout or fixed equipment, a particular bus configuration, or provisions for tie and transfer schemes. Include cable types, conductor sizes, termination preferences, and access needs so the proposed compartment and connection layout can be assessed against the site.
Provide the installation plan, room layout, access route, lifting limits, and required working clearances. Note interface points with transformers, cables, grounding, control wiring, and adjacent equipment. If the project includes replacement work, identify the existing footprint and connection locations, but do not assume new equipment will match them without dimensional and engineering review. Confirm operating, maintenance, and arc-flash requirements with the responsible project team.
Prepare a complete quote and submittal package
For a useful quotation, send the one-line diagram, equipment schedule, fault-current and protection-study data, applicable project specifications, and site constraints. State the required voltage class, insulation criteria, interrupting and withstand duties, circuit functions, enclosure conditions, control power, metering, and accessories. Include the requested submittal, drawing, testing, and documentation scope so these items can be evaluated with the equipment configuration.
Identify the project location in Georgia, delivery point, receiving limitations, required ship-to sequence, and target dates. Delivery planning depends on the final configuration, component availability, production schedule, and shipping details; confirm the applicable scope and timeline for the specific order. Nationwide shipping is available, while site unloading, rigging, installation, and commissioning responsibilities should be assigned separately in the project documents.
Close technical gaps before release
Before approving the order, reconcile the proposed equipment data with the latest one-line diagram and engineering studies. Verify insulation and duty ratings, circuit arrangement, protection interfaces, dimensions, cable terminations, control requirements, and documentation. For switchboard assemblies, UL 891 applies to the switchboard standard where applicable; it is not a blanket listing for medium- or high-voltage switchgear. Confirm the exact equipment type and certification scope for the proposed design.
The practical next step is to assemble the system data and mark unresolved items, including fault-current assumptions, relay functions, site dimensions, and delivery constraints. Submit those details with the requested configuration so the manufacturer can review the application and identify open decisions. Obtain engineering and authority review where required before final approval, installation, or energization.