New electrical distribution equipment, built around your projectServing Georgia
Gray switchgear cabinets with breaker controls and red markings on wooden pallets.

Fabrication

Busbar Punching and Drilling

Busbar connections depend on more than matching hole diameters. For engineers, contractors and purchasing teams in Georgia, the pattern, edge distance, contact face and adjoining clearances all affect whether parts align and can be assembled as intended. We fabricate new switchgear busbars to approved project information and confirm scope before production.

Made in USAUL 891 switchboard assemblies — low voltage onlyAccelerated lead times — confirm availability
Project-specific

Define the application and requirements.

Built in the USA

Discuss equipment and assembly options.

Schedule-aware

Confirm lead times for your order.

Define the connection before detailing holes

Start with the equipment layout and identify each connection point: bus to bus, bus to a device terminal, or bus to a field connection. Share the assembly drawing, bus schedule and the relevant one-line or connection diagram. These documents help distinguish fixed factory joints from interfaces that must meet incoming conductors or another piece of equipment.

For every joint, specify conductor material, bar width and thickness, orientation, number of bars per phase, and the intended fastener arrangement. Include the mating part’s drawing or terminal information when available. Hole locations cannot be finalized reliably from a nominal bar size alone; the actual joint geometry and surrounding assembly determine the pattern.

Make the hole pattern unambiguous

Dimension holes from stated datums, such as a bar end and a designated edge, rather than from a chain of neighboring holes. Give hole diameter, quantity, center-to-center spacing, slot dimensions and slot direction where applicable. Identify whether dimensions apply to each bar separately or to a matched stack, and call out mirrored or handed parts explicitly.

The fastener and mating interface govern the pattern. Clarify bolt size, washer or hardware envelope, terminal-pad dimensions and whether the connection uses round holes or slots. A slot may provide assembly adjustment, but its direction and usable travel must suit the joint; it should not be treated as a substitute for resolving a mismatch in the drawings.

Review edge distance and usable material

Edge distance is measured from the hole center to the nearest bar edge, while end distance is measured to the bar end. Provide the required minimums or the governing engineered detail instead of leaving the fabricator to infer them. The bar’s width, thickness, hole size, material and joint loads all matter to the design decision.

Closely spaced holes, large openings and narrow connecting ligaments can reduce the material available around a joint. Bends, offsets and nearby supports can also constrain where a hole can be made. If a proposed pattern leaves little clearance, flag it during drawing review so the responsible engineer can evaluate a revised layout before fabrication. Do not assume that a hole pattern is acceptable solely because it fits within the bar outline.

Protect the electrical contact surface

Identify the intended mating faces and specify any required surface preparation, plating or finish. Contact areas need to correspond to the approved connection design; paint, coatings, burrs or other material at a mating interface may interfere with the intended joint. State which surfaces must remain clear and whether finish requirements differ between contact zones and exposed bus surfaces.

Hole quality matters at the joint as well as at the edge. Burrs, raised material or damage around an opening can prevent close fit or affect the seating of hardware. Include relevant workmanship notes and inspection expectations in the released specification. Surface treatment, cleaning and handling requirements should be coordinated with the assembly process rather than assumed from a general material description.

Check fit against the real assembly

Before release, compare the busbar detail with the mating terminal and assembly drawings. Check hole-center coordinates, bar orientation, phase spacing, hardware access and clearance to barriers, supports, covers and adjacent conductors. Confirm that the fastener can be inserted and tightened using the intended assembly approach, without relying on forced alignment.

A drawing review can catch inconsistent dimensions, but the project team should also define how fit will be verified. Depending on scope, that may include a dimensional inspection, a trial fit with mating components, or review of an assembly drawing. Identify the controlling revision and approval responsibility so fabrication does not proceed from a superseded pattern.

Prepare a clear fabrication handoff

For a quote, provide the busbar drawings or CAD files, material and finish requirements, quantities, revision status, mating-part details, and any inspection or documentation needs. Note which dimensions are fixed and where engineering review is requested. If information is incomplete, identify the open items rather than treating an assumed hole layout as approved.

For Georgia projects, share the delivery destination, required-on-site date and any receiving or packaging constraints alongside the technical package. We build new switchgear configurations in the United States and coordinate fabrication scope, availability and shipment timing for each order. Send the current connection drawing and mating-interface details for review so the hole pattern, contact faces and fit checks can be resolved before production.

Planning reference

Project specifications

Specifications are confirmed for each order
ScopeRequested by quote
VoltageBased on project requirements
CurrentSpecified to order
ListingDependent on the applicable assembly. UL 891 applies to applicable low-voltage switchboard assemblies, not medium- or high-voltage equipment.
Request a Quote